Analogue Hydrostatic Pressure Testing Equipment

International Equipments

Manufacturers of Analogue Hydrostatic Pressure Testing Equipment

as per IS 4984 and IS 4985 to check the creep rupture of pipe when subjected to internal pressure under a specified condition.

Specification:

Pressure Range : 0 – 100 kg / cm sq.

Time totalizer : Digital presettable with range upto 999.9 hours.

No. of station : 3 nos.

Pressure input : Through compressed air having pressure upto 5 kg / cm sq.

Pressure output : Through hydro-pneumatic pump.

Panel mounting : Trolly with caster wheel.

Paint : Powder coated.

Power : 230V, 50 Hz single phase.

for Details Please Visit International Equipments

PLC based Computerised Hydrostatic Pressure Testing Equipment

International Equipments

Manufacturers of PLC based Computerised Hydrostatic Pressure Testing Equipment

as per IS 4984 and IS 4985 to check the creep rupture of pipe when subjected to internal pressure under a specified condition.

Specification:

Pressure range : 0 – 100 bar*.

No. of stations : 8 nos.

Pressure input : Through compressed air having pressure upto 5 kg/cm.sq

Pressure output: through hydro-pneumatic pump. Time range : 0 – 999.9 hours.

Panel mounting : Trolley with castor wheels.

Paint : Powder coated.

Power : 230 Volts, 50Hz, single phase.

Direct display through MMI : Set pressure, Actual pressure, Set time, Actual time, Set temperature and Actual temperature.

Graphic display and printout through PC : In addition to the above values Pressure & Temperature Vs Time graph could be obtained for any station by attaching a printer to the PC.

for Details Please Visit International Equipments

Digital Hot Air Oven

International Equipments

Manufacturers of Digital Hot Air Oven

with radial air circulation and auto shut facility.

Specification:

Size of working chamber : 12 inch X 12 inch X 12 inch

Material of construction : M.S.

Temperature range : Ambient to 250ºC.

Air circulation : Radial fan (It saves power at least 20% by re-circulating the same hot air inside the oven).

Timer : Digital presettable with range upto 999 minutes.

Paint : Powder coated.

Power supply : 230 Volts, 50Hz, single phase

for Details Please Visit International Equipments

Computerised Humidity chamber

International Equipments

Manufacturers of Computerised Humidity chamber

To determine the effect of relative humidity on sample at various temperatures.

Computerised Humidity chamber to determine the effect of relative humidity on sample at various temperatures.

Specification:

Size of the working chamber : 18 inch X 18 inch x 24 inch

Material of construction :

Inner bath: S.S

Outer body: M.SHumidity

range : 20% RH to 95% RH.

Temperature range : 10ºC to 85ºC

Compressor : CFC free.

Direct display and printout through microcontroller : Set RH, Actual RH, Set temperature and Actual temperature.

Graphic display and printout through PC: In addition to the above values, % RH and Temperature Vs Time graph could be obtained by attaching a printer to the PC.

Paint : Powder coated.

Power : 230 Volts, 50 Hz, Single phase.

for Details Please Visit International Equipments

Digital Opacity Tester

International Equipments

Manufacturers of Digital Opacity Tester

to check the opaqueness of plastic samples as per IS 4985 and IS 12235 (Part 3).

Specification:

Range : 0 – 99.9 % opaque.

Direct display : % opaque.

Paint : Powder coated.

Power : 230 Volts, 50Hz, single phase.

for Details Please Visit International Equipments

Dart Impact Tester

International Equipments

Manufacturers of Dart Impact Tester



Dart Impact Tester

as per ASTM D – 1709 and IS 2508 to test impact resistance of plastic film by free falling dart method.

Specification:

Dart : 2 nos.

Weights : A set of weights ranging from 5 grams to 500 grams would be supplied for incremental loads.

Release mechanism : Electromagnetic.

Vacuum creation : Single stage oil vacuum pump.

Paint : Powder coated.

Power : 230 Volts, 50 Hz, single phase.

for Details Please Visit International Equipments

Analogue VSP / HDT apparatus

International Equipments

Manufacturers of Analogue VSP / HDT Apparatus

as per ASTM D – 1525 and ASTM D – 648 to determine vicat softening temperature and heat deflection temperature of plastics.

Specification:

Temperature range : From ambient to 300ºC.

No of stations : Two.

Material of construction : Inner bath: S.S Outer body: M.S

Rate of heating : 120ºC / hour and 50ºC / hour.

Dial gauge : Range upto 10mm with resolution of 0.01mm.

Weights : A set of weights ranging from 5grams to 2000grams would be supplied for incremental loads.

Paint : Powder coated.

Power : 230 Volts, 50Hz, single phase.

for Details Please Visit International Equipments

Computerised VSP / HDT Apparatus

International Equipments

Manufacturers of Computerised VSP / HDT Apparatus

Computerised VSP - HDT Apparatus

as per ASTM D – 1525 and ASTM D - 648 to determine vicat softening temperature and heatdeflection temperature of plastics.

Specification:

Temperature range : From ambient to 300ºC. No of stations : Two. Material of construction : Inner bath: S.S Outer body: M.S

Rate of heating : 120ºC / hour and 50ºC / hour. Sensor : Range upto 10mm with resolution of 0.01mm.

Weights : A set of weights ranging from 5grams to 2000grams would be supplied for incrementalloads.

Paint : Powder coated.

Power : 230 Volts, 50Hz, single phase.

Graphic display and printout through PC: Penetration/Deflection Vs Temperature graph and numeric reports consisting values of vicat softening temperature and heat deflection temperature could be obtained by attaching a printer to the PC.

for Details Please Visit International Equipments

Motorized Notch Cutter

International Equipments

Manufacturers of Motorized Notch Cutter

Motorized Notch Cutter

for making ‘V’ notch in the Izod / Charpy samples as per ASTM D – 256.

Specification:

Depth micrometer : “Mitutoyo” make.

Range : 0 – 25mm with least count of 0.01mm.

Cutting angle : 45º.

Paint : Powder coated.

Power : 230 Volts, 50Hz, single phase.

DOWNLOAD CATALOGUE

for Details Please Visit International Equipments

Izod Impact Tester

Shanta Engineering

Manufacturer of Izod Impact Tester


Izod Impact Tester

AS PER ASTM D-256

The resistance to breakage by flexural shock of plastics and Electrical insulating materials as indicated by the energy extracted from standardized pendulum type hammers mounted on standardized machines in breaking standard specimens with pendulum swing. The energy absorbed per unit of specimen width is reported in joules.

SPECIFICATION :

Fully digital display ( LCD ) of angle and energy in joules

Range change by selector switch

Interchangeability of impact hammers are very easy.

Max. Available energy - 21.68 Joules

Ranges - 0-2.71 J 0-5.42 J 0-10.84 J 0-21.68 J


OPTIONAL :

1. Dimension feeding facility to calculate Joules / cm2 or Joules / m

2. Torque wrench

3. Charpy hammers

4. Notch cutter ( Manual )

5. Notch cutter ( Motorised )

For More Details Please Visit Shantaengineering

Analogue Izod / Charpy Impact Tester

International Equipments

Manufacturers of Analogue Izod / Charpy Impact Tester



Analogue Izod / Charpy Impact Tester

as per ASTM D - 256 to test impact resistance of plastics. The test indicates the energy required to break standard test specimen.

Specification:

Capacity : Up to 21.68 Joules.

Release angle of pendulum : 150 degree.

Range of four scales : 0-2.71 Joules, 0-5.42 Joules, 0-10.84 Joules and 0-21.68 Joules.

Minimum resolution on scale : 0.02 Joule, 0.05 Joule,0.1 Joule and 0.2 Joule respectively.

Paint : Powder coated.

DOWNLOAD CATALOGUE

for Details Please Visit International Equipments

Computerised Izod Impact Tester

International Equipments

Manufacturers of Computerised Izod Impact Tester


Computerised Izod Impact Tester

Computerised Izod / Charpy Impact Tester

as per ASTM D - 256 to test impact resistance of plastics. The test indicates the energy required to break standard test specimen.

Specification:

Capacity : Up to 25.00 Joules.Release angle of pendulum: 150 degree.

Range of four scales : 0-2.71 Joules, 0-5.42 Joules, 0-10.84 Joules, 0-21.68 Joules and 0-25.00 Joules.Minimum resolution on scale: 0.02 Joule, 0.05 Joule,0.1 Joule, 0.2 Joule and 0.2 Joule respectively.

Paint : Powder coated.

Power : 230 Volts, 50Hz, single phase.

Direct display through microcontroller: Impact strength in joules/meter and kg-cm/cm.

Graphic display and printout through PC: Impact energy Vs Angular displacement graph and numeric reports consisting of values for impact strength as per ASTM standard, ISO and IS standard in different units could be obtained by attaching a printer to the PC.

DOWNLOAD CATALOGUE

for Details Please Visit International Equipments

Computerised Charpy Impact Tester

International Equipments

Manufacturers of Computerised Charpy Impact Tester


Computerised Charpy Impact Tester


Computerised Izod / Charpy Impact Tester

as per ASTM D - 256 to test impact resistance of plastics. The test indicates the energy required to break standard test specimen.

Specification:

Capacity : Up to 25.00 Joules.Release angle of pendulum: 150 degree.

Range of four scales : 0-2.71 Joules, 0-5.42 Joules, 0-10.84 Joules, 0-21.68 Joules and 0-25.00 Joules.Minimum resolution on scale: 0.02 Joule, 0.05 Joule,0.1 Joule, 0.2 Joule and 0.2 Joule respectively.

Paint : Powder coated.

Power : 230 Volts, 50Hz, single phase.

Direct display through microcontroller: Impact strength in joules/meter and kg-cm/cm.

Graphic display and printout through PC: Impact energy Vs Angular displacement graph and numeric reports consisting of values for impact strength as per ASTM standard, ISO and IS standard in different units could be obtained by attaching a printer to the PC.

DOWNLOAD CATALOGUE

for Details Please Visit International Equipments

Melt Flow Index Tester

International Equipments

Manufacturers of Melt Flow Index Tester




Melt Flow Index Tester

Melt Flow Index Tester as per ASTM D – 1238 to measure the flow rates of thermoplastics by extrusion plastometer. This test indicates the uniformity of the flow rate of the polymer.

Melt Flow Index Tester (KAYJAY/2006/AC)

Specification:
Temperature controller:Micro processor based PID controllerwith temperature range from ambientto 400ºC, resolution of 0.1ºC andaccuracy of + 0.1ºC.

Timer : Digital presettable with a rangeup to 59 minutes, 59 seconds.Sample cutting: Auto [Motorized]

Weights : 1.2 kg, 2.16 kg, 3.8 kg,5 kg & 21.6 kg.Accessories : Standard accessories*.Paint : Powder coated.Power : 230 Volts, 50 Hz, single phase.

DOWNLOAD CATALOGUE

Melt Flow Index Tester (KAYJAY/1994/L)

Specification:
Temperature controller : Micro processor basedPID controller with temperature range fromambient to 375ºC, resolution of 0.1ºC andaccuracy of + 0.1ºC.

Timer : Digital presettable with a range up to59 minutes, 59 seconds and having buzzer output.Sample cutting : Manual.

Weights: 1.2 kg, 2.16 kg, 3.8 kg, 5 kg & 21.6 kg.Accessories : Standard accessories*.Paint : Powder coated.Power : 230 Volts, 50 Hz, single phase.

DOWNLOAD CATALOGUE

Melt Flow Index Tester (KAYJAY/2005/CE)

Specification:
Temperature controller: Micro processor based auto tuned PID controller with temperature range from ambient to 400ºC, resolution of 0.1ºC and accuracy of + 0.1ºC.

Timer : Digital presettable with a range up to 999 seconds and having buzzer output.Sample cutting : Manual.

Weights : 2.16 kg & 5 kg.Accessories : Standard accessories*.Paint : Powder coated.Power : 230 Volts, 50 Hz, single phase.

for Details Please Visit International Equipments

Melt Flow Tester

Shanta Engineering

Manufacturer of Melt Flow Tester


Melt Flow Tester

This instrument measures the rate of extrusion of Molten resins through a die of specified length and diameter under prescribed conditions of temperature, load, piston position.

SPECIFICATION

Instrument with following accessories will be suppliedDigital stop watch, Temp. Controller ( PID ), Piston, Orifice remove,Barrel Cleaner, Orifice Cleaner,Scoop, combined weight of 2.16 Kgs.. and 5.0 Kgs.

1. Max. Temp. Ambient to 300°C
2. Resolution : 0.10°C, Accuracy : + 0.20°CTimer 0-99.9 min.

Other Products

Izod & Charpy Impact Tester Oxygen Index Tester Smoke Density Tester Environmental Stress Cracking Tester Electronic Universal Testing Machine VICAT / HDT Tester Kranti Briquetter

Request Quote

Dynamic Balancing Machines

FUEL INSTRUMENTS & ENGINEERS PVT. LTD.

Manufacturer of Dynamic Balancing Machines



Dynamic Balancing Machines

Machines model HDCM are belt driven horizontal type photo scanning Universal Hard Bearing Balancing Machine, provided with microprocessor based measuring panel HDCM – 8500 suitable for balancing different shapes of rotors, of electrical machines, cylinders, fly wheel, rotor of centrifugal pumps and any other type of rotating machines.

These machines are very simple in design. No. drive coupling/ adaptor etc. required to connect to the rotor to be balanced. It has following advantages

1) Coast saving on manufacturing of precision adaptor to connect drive coupling to rotor.

2) Any rotor can be balanced without loosing time in manufacturing of adaptor.

3) The balancing accuracy of rotor not disturbed due to unbalance in drive coupling / adaptor

4) Belt drive machine are more accurate (about 5 times) as compared to end drive machine.

The machines features a very simple operation. The working cycle is fully automatic. From safety point of view a double press push button starts machine, Measures and stores the unbalance values on DPMs for two Plane simultaneously and stops machine. Key board facility provided in measuring panel for correct data deeding of rotor with l digit accuracy for its dimensions like A.B. C, R1 & R2. Tolerance limits of both correction planes i.e.t 11 & t12 can be feed so that when rotor is balanced within the limits respective LEDs glow up, indicating no further correction necessary. For other details please refer “ features of measuring panel HDCM-8500”


STANDARD FEATURES

1) Digital display for unbalance indication Amount and angle of unbalance for both planes displayed on separate DPMs. Hence linear accuracy is very goos as compared to analog meter + /- 1 digit for amount and +/-1 degree for angle.

2) Digital display for RPM indication A DPM is provided to indicate balancing speed continuously as a standard feature.

3) Auto Stop No necessity to stop machine once started. It stops automatically after stabilization of unbalance results.

4) Simultaneous Indication Amount and angle of unbalance in both planes displayed simultaneously and remains displayed (stored ) till next run. This totally eliminates operation of plane selector and reduces additional time for stabilization of readings in other plane.

5) Key-Board Data of rotor dimensions and balancing tolerance i.e. values of A,B,C,R1,R2, t11,t12 are fed by key operation . Hence accuracy of data feeding is accurate up to 1 digit.

6) Tolerance Indicators Separate LEDs are provided for both planes which glow when unbalance is reduced within balancing tolerance.

7) Auto Range Depending upon whether unbalance amount is more or less a respective course or fine range gets automatically selected till rotor gets balanced within tolerance limits, Multiplier operation is totally eliminated.

8) Data store Data of various rotors can be stored against respective rotor type nos. Hence no need of measuring of rotor dimensions or rotor data feeding when repeat balancing operation required. Just call rotor type no. and machine is ready for balancing.

9) Self Check Panel is provided with ‘self-check’ mode which checks proper functioning of digital displays, LEDs is cyclic operation. This helps immediate fault detection.

ADDITIONAL FEATURES ON DEMAND

Printer :

A matrix printer can be connected through ‘FIE’ software. It shows runs till rotor is balanced within balancing tolerance.

Component Indication : ‘FIE’ software specially developed with 3-99 component indication is suitable for balancing of rotor with fixed locations for balancing correction.

Unbalance Correction :

• Drill attachment 8mm capacity portable drill With supporting overhead railing.

• Separate drilling attachment 19mm. Capacity with a vertical drilling head , manual.

• Portable type reverting hammer (piston type) speed 1800 blows/minute, capacity 6mm in a aluminum suspected from top with rail.

• Tangential belt drive, in addition to standard (suitable for a particular type of rotor for production balancing)

• Longitudinal movement of right hand pedestal by chain & sprocket attachment.

TECHNICAL SPECIFICATIONS"FIE" HORIZONTAL HARD BEARING BELT DRIVE DYNAMIC BALANCING MACHINES.

Get Quotation

Dynamic Balancing Machine

FUEL INSTRUMENTS & ENGINEERS PVT. LTD.

Manufacturer of Dynamic Balancing Machine



Dynamic Balancing Machine

Machines Model HDM are horizontal type universal hard bearing balancing machines provided with Microprocessor based measuring panel HDM-8500 for balancing different shapes of rotors like rotors of electrical machines, crankshafts, cylinders, gas compressors, flywheels, turbine rotors, rotors of centrifugal pumps and any other type of rotors of rotating machines.

These machines features a very simple operation. The working cycle is fully automatic. From safety point of view a double press push button starts machine, measures and stores, the unbalance values on DPMs for two planes simultaneously and stop machine ( with brake if machine is provided with electrical breaking facility.) The measuring cycle general is less than 10 seconds for normal rotors which can be accelerated within 5 seconds.

To have smooth and gradual acceleration models HDM - 3,000/- 7,000/- 10,000/- 20,000/-are provided with slipring motors in order not to have damage to drive couplings as well other rotating parts in drive systems like gears etc. The starting of these machines is done manually by cutting resistances of starter in 4 to 5 steps.

key-board facility provided on measuring panel for correct data feeding of rotor with 1 digit accuracy for itsdimensions like A, B, C, R1 & R2. Tolerance limits of both correction plans i.e. tl1 and tl2 can be fed, so that when rotor is balanced within the limits respective LEDs glowup, indicating no further correction necessary. For other details please refer 'Features of Measuring panel HDM-8500'.

The usable length of machine is established according to the longest roter to be balanced.Extension beds can be supplied on request, which can be dded to standard bed of machine. It is also possible to install an additional bed ( Gap bed ) with a pit between this bed and standard bed of machine in order to balance rotors having its outside diameter exceeding swing over standard bed. Models HD-7,000- 10,000/ 20,000 are provided with fixed separate drives and hence gap-bed design is not possible.


STANDARD FEATURES

1) Digital display for unbalance indication Amount and angle of unbalance for both planes displayed on separate DPMs. Hence linear accuracy is very goos as compared to analog meter + /- 1 digit for amount and +/-1 degree for angle.

2) Digital display for RPM indication A DPM is provided to indicate balancing speed continuously as a standard feature.

3) Auto Stop No necessity to stop machine once started. It stops automatically after stabilization of unbalance results.

4) Simultaneous Indication Amount and angle of unbalance in both planes displayed simultaneously and remains displayed (stored ) till next run. This totally eliminates operation of plane selector and reduces additional time for stabilization of readings in other plane.

5) Key-Board Data of rotor dimensions and balancing tolerance i.e. values of A,B,C,R1,R2, t11,t12 are fed by key operation . Hence accuracy of data feeding is accurate up to 1 digit.

6) Tolerance Indicators Separate LEDs are provided for both planes which glow when unbalance is reduced within balancing tolerance.

7) Auto Range Depending upon whether unbalance amount is more or less a respective course or fine range gets automatically selected till rotor gets balanced within tolerance limits, Multiplier operation is totally eliminated.

8) Data store Data of various rotors can be stored against respective rotor type nos. Hence no need of measuring of rotor dimensions or rotor data feeding when repeat balancing operation required. Just call rotor type no. and machine is ready for balancing.

9) Self Check Panel is provided with ‘self-check’ mode which checks proper functioning of digital displays, LEDs is cyclic operation. This helps immediate fault detection.

TECHNICAL SPECIFICATIONS
"FIE" HORIZONTAL TYPE UNIVERSAL HARD BEARING BALANCING MACHINES

Get Quotation

Rockwell Hardness Testing Machines

FUEL INSTRUMENTS & ENGINEERS PVT. LTD.

Manufacturer of Rockwell Hardness Testing Machines



Rockwell Hardness Testing Machines

FEATURES :

ROCKWELL, ROCKWELL BRINELL COMBINED, ROCKWELL/ROCKWELL SUPERFICIAL COMBINED SYSTEM HARDNESS TESTERS.

SAROJ Hardness Testers Model RAS, RAB-1, RAB-250, TWIN are manually operated. All these models are suitable for testing hardness of metals and alloys of all kinds hard or soft, whether flat, round, or irregular shape. These testers are simple in design and easy to operate, yet sensitive & accurate. Various models from the wide range are suitable for schools, laboratories, tool-rooms, inspection, heat treatment departments, factories etc. These testers strictly conform to IS : 3804 -1988, BS : 891 parts 1 & 2, ASTM : E 18 for Rockwell test, IS : 2281 -1983, BS : 240, ASTM : E 10 for Brinell test and IS 5073 -1988 ASTM : E 18 for Rockwell Superficial Test.

MODELS :

STANDARD ACCESSORIES :

TECHNICAL DATA:

LOADS & INDENTORS FOR 'SAROJ' HARDNESS TESTERS FOR ROCKWELL & BRINELL TESTS.